Difference between revisions of "Cisco Air-CAP-2702O-E-K9"

Revision as of 14:16, 15 May 2021

Specifications

Vendor: Cisco

Model: Aironet 2700 Series 802.11ac Dual Band Access Point

Part Number: AIR-CAP2702I-E-K9 v03

System Memory:

• 512 MB DRAM
• 64 MB flash

Power Draw: 15W

Interfaces:

• 2x10/100/1000BASE-T autosensing (RJ-45)
• Management console port (RJ-45)

CPU: PowerPC CPU at 800Mhz, revision number 0x2151 with 376814K/134656K bytes of memory

Console: 9600 8N1, Hardware Flow Control = no, Software Flow Control = no

Entering ROMMON Mode

ROMmon (ROM Monitor) is a bootstrap program that initializes the hardware and boots the Cisco IOS XE software when you power on or reload a router or other device. If your device does not find a valid system image to load when it is booting, the system enters the ROMMON mode.

• Keep the MODE button pressed while providing the device with power until the LED blinks RED.

Reset Factory Default

• Enter ROMMON mode

ap: delete flash:/private-multiple-fs
Are you sure you want to delete "flash:/private-multiple-fs" (y/n)?y
File "flash:/private-multiple-fs" deleted
ap: reset
Are you sure you want to reset the system (y/n)?y
System resetting...

Switch to Standalone Mode

The Aironets support two modes of operations: Autonomous and Lightweight.

The Lightweight mode is for operating with a central controller, thus not requiring extra components (like a webserver for configuring the device through a webinterface).

The Autonomous mode is a full-blown image with all the necessary stuff to manage the device by itself.

We first need to delete all previously install images as they will make it difficult to boot from the correct firmware image.

Delete all previous images

Boot normally on the device (if you do not have access, perform the Factory Reset, the default credentials will be Cisco:Cisco).

Once logged in, look for traces of the current firmware, will typically look something like ap3g2-rcvk9w8-mx or ap3g2-k9w8-mx.153-3.JA10:

APd46d.50fa.02bc>en
Password: (Cisco)
Directory of flash:/

    2  -rwx         269   Jan 1 1970 00:11:45 +00:00  info
    3  -rwx       54810   Jan 6 2020 05:37:36 +00:00  event.log
   39  drwx         576   Mar 1 1993 00:05:54 +00:00  ap3g2-rcvk9w8-mx
    4  -rwx           0   Mar 1 1993 00:00:34 +00:00  config.txt
    5  -rwx         140   Mar 1 1993 00:00:16 +00:00  env_vars
   37  -rwx          64   Jan 6 2020 05:37:28 +00:00  sensord_CSPRNG0
   15  drwx        2176  Oct 18 2016 12:18:57 +00:00  ap3g2-k9w8-mx.153-3.JA10
   71  drwx         320   Mar 1 1993 00:00:15 +00:00  configs
   78  -rwx       59679   May 3 2019 07:57:51 +00:00  event.capwap
   73  -rwx          64   Jan 6 2020 05:37:28 +00:00  sensord_CSPRNG1
    8  -rwx           0  Oct 20 2016 11:17:59 +00:00  ce
    7  -rwx      129753  Mar 15 2018 15:03:21 +00:00  event.r1
    6  -rwx        1048   Mar 1 1993 00:00:20 +00:00  private-multiple-fs
   11  -rwx      128014   Dec 8 2015 19:59:53 +00:00  event.r0
   84  -rwx          74   Mar 3 2020 17:59:32 +00:00  capwap-saved-config-bak
   87  -rwx       95008  Jun 25 2019 10:26:52 +00:00  lwapp_reap.cfg.bak

APd46d.50fa.02bc# delete /recursive /force flash:/ap3g2-rcvk9w8-mx
APd46d.50fa.02bc# delete /recursive /force flash:/ap3g2-k9w8-mx.153-3.JA10

Switch to Autonomous Mode

• Prepare a TFTP Server
• The Cisco device will by default use 10.0.0.1 for its IP, therefore, its recommended that you use 10.0.0.10, but it's not necessary as we can force the device to connect to a specific address.
• The device will expect your firmware tarball to be named something like: "ap3g2-k9w7-tar.default" in your TFTP server root directory. So if your firmware file is called ap3g2-k9w7-tar.153-3.JPI4.tar, replace everything that comes after the first .tar with .tar.default.